Delningsfrekvens subwoofer
Phase tells the subwoofer which direction it should move based upon where it is placed in the room. When a subwoofer is placed close to walls or corners, it can “see” those same surfaces as if they were an extension of the cabinet. In that case, reversing the polarity of only one of them can also disrupt their ability to integrate correctly with each other. So take the time to research, experiment, and find what works best for you!
Spela in subwoofer
First, let me digress a little with an explanation about phase. If your subwoofer and main speakers are in phase, the woofer cones on the subwoofer and the speakers will move forward and backward in sync at the subwoofer crossover frequency. They'll reinforce each other's output. That's good. This will lead to a significant drop off in the bass. Usually, this delay runs from 0 to degrees. Subwoofer crossover inställning
1. Ställ volymen på medel på subben, Crossover på max och phase på 0 till att börja med. 2. Ställ högtalarna en bit från väggen riktad mot där du vanligtvis sitter. 3. Starta upp allting och ställ den medföljande autokalibreringsmikrofonen stadigt i öronhöjd med den rundade delen uppåt, där du vanligtvis brukar sitta. 4. It could result in poor performance and strange tonal characteristics due to destructive interference between multiple subs when reproducing low-frequency content simultaneously. This will lead to a significant drop off in the bass. Ställa in subwoofer
If the subwoofer is in line with the front speakers, its bass speaker should have the same direction of movement (phase) - the controller on the woofer is set to "0". If the subwoofer is not between the front speakers, but is to the side of or even behind the listening location, its phase length will not match that of the front speakers. These subwoofer phase settings are often referred to as normal and reverse phases, respectively. Phase 0 is possible when the speaker and the sub are in the same room or place. Subben
Låt High Pass på subwoofern stå på Off. Börja sedan med att justera volymen/nivån så att subwoofern och fronthögtalarna spelar lika hög volym. Justera därefter fasen (Phase) så ni få så mycket bastryck som möjligt, då är man hyfsat rätt i fas och subben spelar mer tillsammans med frontarna. Corner placement can enhance bass but may lead to standing wave issues. The right phase setting ensures that bass is neither too pronounced nor too subdued, striking the perfect balance for an immersive audio experience. Room acoustics, speaker placement, and personal preferences should all be considered when determining the best setting for a given situation. Mastering Subwoofer Setup: The Ultimate Guide for Home Theater Enthusiasts
Subwoofer Pros and Cons. Adding an actively powered subwoofer can greatly increase your system’s dynamic range, bass extension, midrange clarity, and ability to play louder without strain. The additional amplifier power and low-frequency driver allow the system to reproduce musical peaks at higher levels. Moreover, removing low frequencies. Adjusting these parameters is crucial for the subwoofer to work in harmony with other speakers in the home theater system. Save my name, email, and website in this browser for the next time I comment. Save my name, email, and website in this browser for the next time I comment. 
Subwoofer Phase 0 Or 180? (Why Does It Matter?)
Subwoofer Phase This is also called the reverse phase. As the name implies, this phase reverses the subwoofer’s polarity. Hence, the sub is placed in opposite polarity to the main speaker. In this case, the inward movement of the subwoofer’s driver will cause an outward movement of all the speaker drivers. This type of setting is ideal if you are ready to have the sub and main speaker on the opposite sides of the place or room. In short, the proper setup of any audio system requires research, trial-and-error testing, patience, and time if you want to get the most out of it both sonically and aesthetically. 
› forum › topic.
Once the ancillary speakers are installed and tuned to your PA, you’ll need to time-align them with the main speakers so that sound coming from the delayed speakers arrives at the audience in time with the sound from the main speakers. Otherwise, the difference in arrival time between the mains and ancillary speakers will create sonic problems. Manual room correction requires assistance from acoustic testing equipment. Regarding subwoofers, the reverse phase can be beneficial in some cases but not all.